Meyer Sound MP-4 Instructions d'exploitation

Keep these important operating instructions. Check www.meyersound.com for updates.OPERATING INSTRUCTIONS INDUSTRIAL SERIESMPS-488HP Power Supply

CHAPTER 2: MPS-488HP FRONT AND REAR PANELS10Green Load Current LEDs (1–8)The green Load Current LEDs indicate whether loudspeak-ers are connected to t

MPS-488HP OPERATING INSTRUCTIONS11Link SwitchesLink switches determine how Channel Inputs are routed to Channel Outputs. When a Channel Input’s Link s

CHAPTER 2: MPS-488HP FRONT AND REAR PANELS12To avoid distortion when linking Channel Inputs, make sure the source device can drive the total load impe

MPS-488HP OPERATING INSTRUCTIONS13MPS-488HP CURRENT DRAWThe current draw for the MPS-488HP and its connected loudspeakers is dynamic and fluctuates as

CHAPTER 2: MPS-488HP FRONT AND REAR PANELS14

15CHAPTER 3: CONNECTING LOUDSPEAKERS TO THE MPS-488HPNOTE: For information on cable requirements for your loudspeaker, refer to its operating instruct

CHAPTER 3: CONNECTING LOUDSPEAKERS TO THE MPS-488HP16 When connecting loudspeakers equipped with EN3 con-nectors to the MPS-488HPe power supply, use

17APPENDIX A: MPS-488HP ACCESSORIESPHOENIX AND EN3 CABLE CONNECTORS AND ADAPTERSThe following cable connectors and adapters are available from Meyer S

APPENDIX A: MPS-488HP ACCESSORIES1828.163.009.31 EN3 5-pin female to EN3 5-pin male White Plenum 10 ft28.163.009.32 20 ft28.163.009.33 30 ft28.163.009

19APPENDIX B: PHOENIX AND EN3 CABLE ASSEMBLYCAUTION: When wiring cable connections for MPS-488HP Channel Outputs, it is extremely important that each

iiDECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014© 2011 Meyer Sound. All rights reserved.MPS-488HP Operating Instructions, PN 05

APPENDIX B: PHOENIX AND EN3 CABLE ASSEMBLY202. If the cable has not been stripped, strip the outer shielding 1 inch and then strip the black, red, blu

MPS-488HP OPERATING INSTRUCTIONS215. Repeat the previous steps to attach the EN3 5-pin female connector to the other end of the cable.ASSEMBLING EN3-T

APPENDIX B: PHOENIX AND EN3 CABLE ASSEMBLY222. Insert the five exposed conductors into the five cable holes in the Phoenix connector using the followi

MPS-488HP OPERATING INSTRUCTIONS236. Solder the five exposed conductors to the five pins on the EN3 cord connector using the following wiring scheme.7

APPENDIX B: PHOENIX AND EN3 CABLE ASSEMBLY242. Insert the five exposed conductors, from one end of the cable, into the five cable holes in one of the

25APPENDIX C: MPS-488HP SPECIFICATIONSMPS-488HP SpecificationsFRONT PANELLEDs Eight LEDs to indicate output voltageEight LEDs to indicate load current

APPENDIX C: MPS-488HP SPECIFICATIONS26MPS-488HP ComplianceMPS-488HP SpecificationsCurrent Draw with Eight MM-10XP SubwoofersIdle Current 0.74 A rms (1

MPS-488HP OPERATING INSTRUCTIONS27MPS-488HPp DIMENSIONSMPS-488HPp Dimensions19.00 [483 mm]16.90 [429 mm]1.73 [44 mm]14.10 [358 mm]13.57 [345 mm]

APPENDIX C: MPS-488HP SPECIFICATIONS28MPS-488HPe DIMENSIONSMPS-488HPe Dimensions19.00 [483 mm]16.90 [429 mm]1.73 [44 mm]14.33 [364 mm]13.57 [345 mm]

iiiSYMBOLS USEDThese symbols indicate important safety or operating features in this booklet and on the chassis:IMPORTANT SAFETY INSTRUCTIONS1. Read t

Meyer Sound Laboratories Inc. 2832 San Pablo Avenue Berkeley, CA 94702www.meyersound.com T: +1 510 486.1166 F: +1 510 486.8356© 2011Meyer Sound. All r

ivSAFETY SUMMARYEnglish To reduce the risk of electric shock, dis-connect the apparatus from the AC mains before installing audio cable. Reconnect th

vCONTENTSChapter 1: Introduction 7How to Use This Manual 7MPS-488HP External Power Supply 7Chapter 2: MPS-488HP Front and Rear Panels 9MPS-488HP Front

CONTENTSvi

7CHAPTER 1: INTRODUCTIONHOW TO USE THIS MANUALMake sure to read these operating instructions in their entirety before configuring a loudspeaker system

CHAPTER 1: INTRODUCTION8ticonductor cables (such as Belden® 1502 or equivalent) allows a single cable to carry both audio and DC power from the MPS-48

9CHAPTER 2: MPS-488HP FRONT AND REAR PANELSMPS-488HP FRONT PANELThe MPS-488HP front panel includes a power switch and LEDs for monitoring each loudspe