Keep these important operating instructions. Check www.meyersound.com for updates.OPERATING INSTRUCTIONSINDUSTRIAL SERIESMM-10 Miniature SubwooferMPS
CHAPTER 1: INTRODUCTION10MM-10XP SubwooferThe MM-10XP is powered by an external 48 V DC power supply, eliminating the need for wiring conduits while s
11CHAPTER 2: MM-10XP SUBWOOFERThe MM-10XP is powered by an external 48 V DC power supply, eliminating the need for wiring conduits while still preserv
CHAPTER 2: MM-10XP SUBWOOFER12MM-10XP INPUT POLARITY SWITCHThe Input Polarity switch swaps the polarity of the audio source signal, which is sometimes
MM-10 OPERATING INSTRUCTIONS13MM-10XP Temperature and LimitingThe Limit LED turns solid yellow when its heat sink tempera-ture reaches 65° C (145° F),
CHAPTER 2: MM-10XP SUBWOOFER14WIRING MM-10XP LOUDSPEAKER CABLES WITH BELDEN 1502 CABLEWhen wiring MM-10XP loudspeaker cables with Belden 1502 or an eq
15CHAPTER 3: POWERING MM-10XP SUBWOOFERS WITH THE MPS-488HPThe MPS-488HP power supply delivers DC power and bal-anced audio to Meyer Sound loudspeaker
CHAPTER 3: POWERING MM-10XP SUBWOOFERS WITH THE MPS-488HP16MPS-488HP REAR PANELThe MPS-488HP rear panel includes an AC Input connector, eight Channel
MM-10 OPERATING INSTRUCTIONS17Routing Two Inputs to Four Outputs EachTo route two Channel Inputs to four Channel Outputs each:1. Set the Link 4 switch
CHAPTER 3: POWERING MM-10XP SUBWOOFERS WITH THE MPS-488HP18MPS-488HPp Channel OutputsThe MPS-488HPp Channel Outputs use Phoenix 5-pin male connectors
MM-10 OPERATING INSTRUCTIONS19SAFETY ISSUESPay close attention to these important electrical and safety issues. The MPS-488HP requires a grounded out
iiDECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014© 2010 Meyer Sound. All rights reserved.MM-10 Operating Instructions, PN 05.199
CHAPTER 3: POWERING MM-10XP SUBWOOFERS WITH THE MPS-488HP20a larger gauge for the DC cable so you can achieve longer cable runs (see “Cable Lengths an
21CHAPTER 4: MM-10AC SUBWOOFERThe MM-10AC subwoofer includes an internal power supply and locking AC PowerCon connectors. The MM-10AC receives audio f
CHAPTER 4: MM-10AC SUBWOOFER22Each MM-10AC ships with one AC looping connector for making AC looping cables. Assembled AC looping cables are available
MM-10 OPERATING INSTRUCTIONS23 Ultimate Short-Term Peak Current — A rating for fast-reacting magnetic breakers. Inrush Current — The spike of initia
CHAPTER 4: MM-10AC SUBWOOFER24 Pin 3 — Signal (–) Case — Earth (AC) ground and chassisPins 2 and 3 carry the input as a differential signal. Pin 1 i
MM-10 OPERATING INSTRUCTIONS25Powering On (Green)When powering up the MM-10AC subwoofer, the following startup events occur and are indicated by the L
CHAPTER 4: MM-10AC SUBWOOFER26
27CHAPTER 5: MM-10ACX SUBWOOFERThe MM-10ACX subwoofer includes onboard DC power and audio routing for driving satellite loudspeakers: up to two MM-4XP
CHAPTER 5: MM-10ACX SUBWOOFER28AC Loop Output Connector (Gray)The gray AC Loop Output connector allows multiple MM-10ACX subwoofers to be looped and p
MM-10 OPERATING INSTRUCTIONS29CAUTION: The power source for the MM-10ACX should always operate within the required voltage range, at least a few volts
iiiFEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, p
CHAPTER 5: MM-10ACX SUBWOOFER30ELECTRICAL SAFETY ISSUESPay close attention to these important electrical and safety issues. The MM-10ACX requires a g
MM-10 OPERATING INSTRUCTIONS31MM-10ACX SATELLITE OUT CONNECTORSThe Satellite Out connectors deliver DC power (48 V DC) and balanced audio to satellite
CHAPTER 5: MM-10ACX SUBWOOFER32NOTE: The Input Select switch is only included on the MM-10ACX model. The switch only affects the subwoofer signal and
MM-10 OPERATING INSTRUCTIONS33CAUTION: If the Limit LED turns red and stays solid red after powering up and the audio is muted, the subwoofer has enco
CHAPTER 5: MM-10ACX SUBWOOFER34MM-10ACX SATELLITE CONFIGURATIONS Single ChannelTo configure a single-channel satellite system with one MM-10ACX and ei
MM-10 OPERATING INSTRUCTIONS35Dual ChannelTo configure a dual-channel satellite system with one MM-10ACX and two MM-4XPs:1. Connect the left audio sig
CHAPTER 5: MM-10ACX SUBWOOFER36Dual Channel + Sub Channel (2.1)To configure a 2.1 satellite system with one MM-10ACX and two MM-4XPs:1. Connect the le
37CHAPTER 6: MOUNTING THE MM-10The MM-10 is available with top and side nut plates with either 3/8"-16 or metric M10 threaded nuts. The optional
CHAPTER 6: MOUNTING THE MM-1038Wall-Mounting with the MUB-MM10The MUB-MM10 U-bracket lets you mount the MM-10 either vertically or horizontally on a w
39APPENDIX A: MM-10 ACCESSORIESMM-10 ACCESSORIESThe following MM-10 accessories are available from Meyer Sound.PHOENIX AND EN3 CABLE CONNECTORS AND AD
ivSYMBOLS USEDThese symbols indicate important safety or operating features in this booklet and on the chassis:IMPORTANT SAFETY INSTRUCTIONS1. Read th
APPENDIX A: MM-10 ACCESSORIES40PHOENIX AND EN3 LOUDSPEAKER CABLESThe following Phoenix and EN3 cables are available from Meyer Sound and can be used t
41APPENDIX B: OPTIONAL RAIN HOODSA weather-protected version of the MM-10 subwoofer is avail-able with rain hood kits that safeguard the subwoofer’s e
APPENDIX B: OPTIONAL RAIN HOODS424. Attach the rain hood by slipping it under the flange on the right side of the subwoofer, placing it flush against
43APPENDIX C: PHOENIX AND EN3 CABLE ASSEMBLYASSEMBLING EN3-TO-EN3 LOUDSPEAKER CABLESWhen connecting MM-10XP loudspeakers equipped with EN3 connectors
APPENDIX C: PHOENIX AND EN3 CABLE ASSEMBLY442. If the cable has not been stripped, strip the outer shielding 1” and then strip the black, red, blue, a
MM-10 OPERATING INSTRUCTIONS455. Repeat the previous steps to attach the EN3 5-pin female connector to the other end of the cable.ASSEMBLING EN3-TO-PH
APPENDIX C: PHOENIX AND EN3 CABLE ASSEMBLY462. Insert the five exposed conductors into the five cable holes in the Phoenix connector using the followi
MM-10 OPERATING INSTRUCTIONS476. Solder the five exposed conductors to the five pins on the EN3 cord connector using the following wiring scheme.7. Re
APPENDIX C: PHOENIX AND EN3 CABLE ASSEMBLY482. Insert the five exposed conductors, from one end of the cable, into the five cable holes in one of the
49APPENDIX D: SPECIFICATIONSMM-10 SPECIFICATIONS (ALL MODELS)MM-10 Specifications (All Models)ACOUSTICALOperating Frequency Range 33 Hz – 228 HzNote:
vSAFETY SUMMARYEnglish To reduce the risk of electric shock, dis-connect the loudspeaker from the AC mains before installing audio cable. Reconnect t
APPENDIX D: SPECIFICATIONS50MM-10XP SpecificationsENVIRONMENTALOperating Temperature 0° C to +45° CNon Operating Temperature <–40° C or >+75° CH
MM-10 OPERATING INSTRUCTIONS51MM-10AC SpecificationsMM-10AC SpecificationsMM-10AC REAR PANELAudio Connectors XLR female input with XLR male loop outpu
APPENDIX D: SPECIFICATIONS52MM-10ACX SpecificationsMM-10ACX SpecificationsMM-10ACX REAR PANELSubwoofer Audio Connector XLR female inputPin 1: Chassis/
MM-10 OPERATING INSTRUCTIONS53MM-10 COMPLIANCEMM-10 DIMENSIONSNote: Current draw values for one MM-10ACX with two MM-4XP satellite loudspeakers connec
APPENDIX D: SPECIFICATIONS54
Meyer Sound Laboratories Inc.2832 San Pablo AvenueBerkeley, CA 94702www.meyersound.comT: +1 510 486.1166F: +1 510 486.8356© 2010Meyer Sound. All r
viiCONTENTSChapter 1: Introduction 9How to Use This Manual 9MM-10 Miniature Subwoofer 9MM-10 Options 10Chapter 2: MM-10XP Subwoofer 11MM-10XP Input Co
CONTENTSviiiAppendix A: MM-10 Accessories 39Appendix B: Optional Rain Hoods 41Appendix C: Phoenix and EN3 Cable Assembly 43Appendix D: Specifications
9CHAPTER 1: INTRODUCTIONHOW TO USE THIS MANUALMake sure to read these operating instructions in their entirety before configuring a loudspeaker system
Commentaires sur ces manuels