Keep these important operating instructions. Check www.meyersound.com for updates.OPERATING INSTRUCTIONSCINEMA EXPERIENCEHMS-10™ Surround Loudspeaker
CHAPTER 2: THE MPS-488P POWER SUPPLY10NOTE: Since HMS-10s should only be con-nected to channel outputs 1, 3, 5, and 7, only the Load Current LEDs for
HMS-10 OPERATING INSTRUCTIONS11Routing One Input to Four OutputsTo route one audio input to four channel outputs: Set all Link switches to ON.Routing
CHAPTER 2: THE MPS-488P POWER SUPPLY12Each MPS-488P comes with Phoenix 5-pin female cable connectors for assembling HMS-10 loudspeaker cables. For inf
HMS-10 OPERATING INSTRUCTIONS13 Do not use a ground-lifting adapter or cut the AC cable ground pin. Keep all liquids away from the MPS-488P to avoid
CHAPTER 2: THE MPS-488P POWER SUPPLY14
15CHAPTER 3: THE HMS-10 LOUDSPEAKERTHE HMS-10 CONNECTORThe HMS-10 receives DC power and balanced audio from a Phoenix 5-pin male connector on its top
CHAPTER 3: THE HMS-10 LOUDSPEAKER16Cable Lengths and Cable Gauges for HMS-10sWhen connecting an HMS-10 to an MPS-488P channel out-put, you can use cab
17CHAPTER 4: MOUNTING THE HMS-10The HMS-10 comes standard with a fixed bracket; an adjustable bracket is also available for wall mounting the HMS-10 w
CHAPTER 4: MOUNTING THE HMS-1018To mount the HMS-10 with the fixed mount bracket:1. Disassemble the fixed bracket by removing the two bot-tom screws.
HMS-10 OPERATING INSTRUCTIONS19MOUNTING THE HMS-10 WITH THE ADJUSTABLE MOUNT BRACKETThe HMS-10 can be wall mounted with the adjustable mount bracket a
iiDECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014© 2009 Meyer Sound. All rights reserved.HMS-10 Operating Instructions, PN 05.19
CHAPTER 4: MOUNTING THE HMS-10205. Adjust the tilt of the HMS-10 from –13 degrees (downtilt) to +5 degrees (uptilt). Tighten the four side screws to s
21APPENDIX A: HMS-10 ACCESSORIESThe following HMS-10 accessories are available from Meyer Sound.NOTE: Belden 1502 is a composite cable comprised of tw
APPENDIX A: HMS-10 ACCESSORIES22
23APPENDIX B: HMS-10 CABLE ASSEMBLYASSEMBLING PHOENIX-TO-PHOENIX LOUDSPEAKER CABLESTo connect the HMS-10 loudspeaker directly to the MPS-488P power su
APPENDIX B: HMS-10 CABLE ASSEMBLY243. Secure the conductors by tightening the five screws in the Phoenix connector.4. Repeat the previous steps and at
25APPENDIX C: HMS-10 SPECIFICATIONSHMS-10 SpecificationsACOUSTICALOperating Frequency Range 55 Hz – 18 kHzNote: Recommended maximum operating frequenc
APPENDIX C: HMS-10 SPECIFICATIONS26HMS-10 COMPLIANCEOutput Power 300 W totalNote: Wattage rating based on the maximum unclipped burst sine-wave rms vo
HMS-10 OPERATING INSTRUCTIONS27HMS-10 DIMENSIONSHMS-10 Dimensions with Fixed Bracket (OmniMount 17FM-F)5.60 [142 mm]13.05 [331 mm]12.48 [317 mm]6.87 [
APPENDIX C: HMS-10 SPECIFICATIONS28
29APPENDIX D: MPS-488 SPECIFICATIONSNOTE: The MPS-488 was originally designed for use with the MM-4XP miniature loudspeaker. While the MPS-488 can pow
iiiSYMBOLS USEDThese symbols indicate important safety or operating features in this booklet and on the chassis:IMPORTANT SAFETY INSTRUCTIONS1. Read t
APPENDIX D: MPS-488 SPECIFICATIONS30MPS-488 COMPLIANCEMPS-488 DIMENSIONSNon Operating AltitudeTo 95% at 35° CShock30 g 11 msec half-sine on each of 6
Meyer Sound Laboratories Inc. 2832 San Pablo Avenue Berkeley, CA 94702www.meyersound.com T: +1 510 486.1166 F: +1 510 486.8356© 2009Meyer Sound. All r
ivSAFETY SUMMARYEnglish To reduce the risk of electric shock, dis-connect the loudspeaker from the AC mains before installing audio cable. Reconnect
vCONTENTSChapter 1: Introduction 7How to Use This Manual 7the HMS-10 Surround Loudspeaker 7Chapter 2: The MPS-488P Power Supply 9The MPS-488P Front Pa
CONTENTSvi
7CHAPTER 1: INTRODUCTIONHOW TO USE THIS MANUALMake sure to read these operating instructions in their entirety before configuring a loudspeaker system
CHAPTER 1: INTRODUCTION8HMS-10 loudspeaker systems require an MPS-488P exter-nal power supply. The single-space 19-inch rack unit receives balanced au
9CHAPTER 2: THE MPS-488P POWER SUPPLYThe MPS-488P power supply delivers DC power and bal-anced audio to Meyer Sound loudspeakers that require a 48 V D
Commentaires sur ces manuels