Meyer Sound HMS-10 Instructions d'exploitation

Keep these important operating instructions. Check www.meyersound.com for updates.OPERATING INSTRUCTIONSHMS-10™ Surround Loudspeaker

CHAPTER 2: HMS-10 LOUDSPEAKER10Calculating the Maximum Cable LengthThe maximum cable length for an HMS-10 can be calcu-lated with the following formul

11CHAPTER 3: POWERING HMS-10 LOUDSPEAKERSCONNECTING HMS-10 LOUDSPEAKERS TO THE MPS-488HP EXTERNAL POWER SUPPLYHMS-10 loudspeakers require a Meyer Soun

CHAPTER 3: POWERING HMS-10 LOUDSPEAKERS12CONNECTING HMS-10 LOUDSPEAKERS TO THE MPS-488 EXTERNAL POWER SUPPLYThe original MPS-488 was designed for use

13CHAPTER 4: MOUNTING HMS-10 LOUDSPEAKERSThe HMS-10 comes standard with a fixed bracket; an adjustable bracket is also available for wall mounting the

CHAPTER 4: MOUNTING HMS-10 LOUDSPEAKERS14To mount the HMS- 10 w ith th e fixed mount brack et :1. Disassemble the fixed bracket by removing the two b

HMS-10 OPERATING INSTRUCTIONS15MOUNTING HMS-10 LOUDSPEAKERS WITH THE ADJUSTABLE MOUNT BRACKETThe HMS-10 can be wall mounted with the adjustable mount

CHAPTER 4: MOUNTING HMS-10 LOUDSPEAKERS165. Adjust the tilt of the HMS-10 from –13 degrees (downtilt) to +5 degrees (uptilt). Tighten the four side sc

17APPENDIX A: HMS-10 ACCESSORIESThe following HMS-10 accessories are available from Meyer Sound.NOTE: The MPS-488HP external power supply replaces the

APPENDIX A: HMS-10 ACCESSORIES18

19APPENDIX B: HMS-10 CABLE ASSEMBLYCAUTION: When wiring HMS-10 loudspeaker cables, it is extremely important that each pin be wired correctly. Make su

iiDECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014© 2009, 2011Meyer Sound. All rights reserved.HMS-10 Operating Instructions, PN

APPENDIX B: HMS-10 CABLE ASSEMBLY203. Secure the conductors by tightening the five screws in the Phoenix connector.4. Repeat the previous steps and at

21APPENDIX C: HMS-10 SPECIFICATIONSHMS-10 SpecificationsACOUSTICALOperating Frequency Range 55 Hz – 18 kHzNote: Recommended maximum operating frequenc

APPENDIX C: HMS-10 SPECIFICATIONS22HMS-10 COMPLIANCEOutput Power 300 W totalNote: Wattage rating based on the maximum unclipped burst sine-wave rms vo

HMS-10 OPERATING INSTRUCTIONS23HMS-10 DIMENSIONSHMS-10 Dimensions with Fixed Bracket (OmniMount 17FM-F)5.60 [142 mm]13.05 [331 mm]12.48 [317 mm]6.87 [

APPENDIX C: HMS-10 SPECIFICATIONS24

Meyer Sound Laboratories Inc.2832 San Pablo AvenueBerkeley, CA 94702www.meyersound.comT: +1 510 486.1166F: +1 510 486.8356© 2009, 2011Meyer Sound.

iiiSYMBOLS USEDThese symbols indicate important safety or operating features in this booklet and on the chassis:IMPORTANT SAFETY INSTRUCTIONS1. Read t

ivSAFETY SUMMARYEnglish To re duc e th e ris k of elect ric sho ck, di s-connect the loudspeaker from the AC mains before installing audio cable. R

vCONTENTSChapter 1: Introduction 7How to Use This Manual 7HMS-10 Surround Loudspeaker 7Chapter 2: HMS-10 Loudspeaker 9HMS-10 Input Connector 9HMS-10 C

CONTENTSvi

7CHAPTER 1: INTRODUCTIONHOW TO USE THIS MANUALMake sure to read these operating instructions in their entirety before configuring a loudspeaker system

CHAPTER 1: INTRODUCTION8Balanced audio and DC power are received by the HMS-10 from a Phoenix™ 5-pin male connector on its top panel. Powering the uni

9CHAPTER 2: HMS-10 LOUDSPEAKERHMS-10 INPUT CONNECTORThe HMS-10 receives DC power and balanced audio from its Phoenix 5-pin male connector on the top p